Pool Heater Won't Turn On? What to Check First
First cool night of the season and no heat? Most heater problems come down to a few simple causes.

The most common reasons a pool heater or heat pump will not start are low water flow, a dirty filter, the pump not running, the thermostat set lower than the water temperature or the heater being switched to off or standby. Gas heaters can also be stopped by a closed gas valve or empty propane tank. Heat pumps may not run when the air is too cold. Check these first before assuming the heater has failed.
Safety first
If you smell gas, do not try to start the heater. Leave the area and call your gas company. Gas lines, burners, ignition systems and electrical components should only be worked on by a qualified professional.
Start with water flow
Pool heaters have a safety switch that stops them firing unless enough water is moving through them. Low flow is the number one reason heaters will not start.
- •Make sure the pump is running.
- •Empty the skimmer and pump baskets.
- •Check the filter pressure and clean the filter if it is high.
- •Make sure all valves are open in the right positions.
- •Check that the water level is high enough for the skimmer to work properly.
Gas heater: common causes
| Problem | What to check |
|---|---|
| Heater will not fire | Pump running, filter clean, valves open, thermostat set above the water temperature |
| Heater shows an error code | Look up the code in your heater's manual |
| No gas reaching the heater | Gas valve open, propane tank not empty |
| Heater starts then shuts off | Low flow, a dirty filter or a safety switch tripping |
| Heater is in standby or off | Control panel set to pool or spa heat mode |
Heat pump: common causes
| Problem | What to check |
|---|---|
| Heat pump will not start | Pump running, filter clean, thermostat set above water temperature |
| Fan runs but no heat | Air temperature may be too low, or the unit is in a defrost cycle |
| Slow to start | Many heat pumps have a built-in delay of a few minutes before starting |
| Ice on the coils | Normal in cooler weather if it clears in a defrost cycle; ongoing icing needs checking |
| Airflow blocked | Clear leaves and debris from around the unit |
Checked the basics and still no heat? Call 678-691-6124 or stop by our Alpharetta store at 2900 Holcomb Bridge Rd to talk through what you are seeing.
Heat pumps and cold weather
Heat pumps pull warmth from the air, so they work less effectively as temperatures drop and may stop running altogether in cold weather. That is normal, not a fault. If you want to swim in colder months, a gas heater is usually the better option. Read our guide to pool heater vs heat pump in Georgia.
Check your manual
Most heaters display an error code when something is wrong, and your manual explains what each code means. Lost yours? Read our guide to finding pool equipment manuals and parts diagrams.
Keep your heater healthy
- •Keep your filter clean so water flows freely.
- •Keep your water balanced. Low pH and water that is out of balance can damage heater parts over time.
- •Keep the area around the heater clear of leaves and debris.
- •Protect your heater during freezing weather by keeping water moving or properly draining it.
Read our guide to pool filter cleaning.
Frequently asked questions
Still no heat?
Pool Supply Atlanta helps pool owners across Alpharetta, Roswell, Milton, Johns Creek and Sandy Springs. Visit us at 2900 Holcomb Bridge Rd, Alpharetta, GA 30022 (Mon to Fri 9am to 5pm, Sat 9am to 4pm) or call 678-691-6124.
Related Pool Articles
The Ultimate Atlanta Spring Pool Opening Checklist (2026 Edition)
Spring weather in North Georgia comes early! Here is your step-by-step checklist to open your Alpharetta or Roswell pool crystal clear.
How to Clear Green Pool Water Fast in Georgia Summer Heat
Hot Georgia sun and sudden thunderstorms can turn a pool green overnight. Follow our proven 4-step green-to-clean recovery plan.
